| |
|
|
Fasteners G/S
 |
 |
Sarnabar 6
For fastening to substrates such as steel, wood, etc. Holes spaced at
25 mm for fasteners up to ø 6,5 mm.
Sarnabar 10/6
For fastening to substrates such as concrete, lightweight concrete, hollow concrete elements, etc.). Holes spaced at 25 mm, staggered, for fasteners from ø 6,5 to 10 mm.
|
|
 |
|
Sarnafast Barbed Washer
KT 82 x
40
For in-seam securement of Sarnafil TS through the insulation layer.
Galvanised
steel 1 mm, with diamond-shaped reinforcing and 8 specially stamped barbs. Size: 82 x 40 mm.
diameter
4,9 mm.
Use only with Sarnafast SF 4,8 x L screws. With the ø 6.0 mm
shanks this assembly
safely supports foot traffic.
|
|
 |
|
Sarnafast Barbed Washer KTL 82
x 40
For in-seam securement of Sarnafil TS through the insulation layer.
Galvanised
steel 1 mm, with diamond-shaped reinforcing and 8 specially
stamped barbs. Size: 82
x 40 mm.
Hole diameter 7,5 mm.
Use with SFS Spike D, Isofast IG-6 x L,
or Isofast IE
fasteners.
|
|
 |
|
Sarnafast RT 90 Row Termination Plate
For
terminating a row of fasteners (Sarnafast System or Sarnabar System) at ends and corners, installed
over insulation.
Galvanised steel, 1 mm thick. Diameter 90 mm. Secured with 4 Sarnafast
screws.
Hole diameter 4,9 mm. Use with Sarnafast SF 4.8 x L screws.
Sarnafast
RT 90 Row Termination Plates are not to be installed in seams.
|
|
 |
|
Sarnafast RTL 90 Row Termination Plate
For
terminating a row of fasteners (Sarnafast System or Sarnabar System) at ends and corners, applied over
insulation.
Galvanised steel, 1 mm thick. Diameter 90 mm. Secured with 4 Sarnafast screws.
Hole
diameter 7,5 mm. Use with SFS Spike D, Isofast IG-6 x L, or Isofast IE fasteners. Sarnafast RTL 90 Row
Termination Plates are not to be installed in seams.
|
|
 |
|
Sarnafast Insulation WasherDT 70 x 70
For
fastening rigid insulation. Galvanised steel, 1 mm thick.
70 x 70 mm. Hole diameter
4,9 mm. Use with Sarnafast SF 4.8 x L screws. With the Ø 6,0 mm shanks this assembly safely supports
foot traffic. Sarnafast DTL 70 x 70 Insulation Washers are not to be installed in seams.
|
|
 |
|
Sarnafast Insulation WasherDTL 70 x 70
For
fastening rigid insulation. Galvanised steel, 1 mm thick.
70 x 70 mm. Hole diameter
7,5 mm. Use with SFS Spike D, Isofast IG-6 x L, or Isofast IE fasteners. Sarnafast
DTL
70 x 70 Insulation Washers are not to be installed in seams.
|
|
 |
|
Load Distribution Plate
For terminations
at ends and corners in the Sarnabar System. Not for use in Sarnafast systems.
|
|
|
|
Sarnafast
Screws
Sarnafast screws are used as fasteners in the Sarnabar System and the Sarnafast
System. They perfectly match Sarnafast barbed washers and are protected against corrosion with Durocoat.
Sarnafast
screws are suitable for fastening to these substrates:
- corrugated
steel decks from 0,75 mm to 2 x 1,25 mm
- wood planks, wood framing,
plywood (particle board is unsuitable as a roof deck), that
offer at least 24 mm of penetration.
|
|
 |
|
Sarnafast screws are available in two formats:
loose and collated (up to
240 mm). Collated
Sarnafast screws can be driven automatically using a modified SFS screw gun.
Manufacturer’s
recommendations apply for thread lengths of common screws available through Sarnafil (rule of thumb:
thread length + 20 mm = screw length).
Brochure
Sarnafast |
© 2004 Sarnafil International AG Legal Disclaimer
|
|
